Modelling bits for 3d printing

[Malika]

So this just happened...

https://www.instagram.com/p/B1Td-OCovDc/

[Stormwind]

Oh nice, are these like, Skinnerz infantry leaders being re-done?

[Malika]

I basically designed a bunch of Skinners wearing heavy War Rigs, basically heavy sets of armour that in the long ago used to be mining equipment, but now turned into military gear. I did a set of 8 'regular' heavily armoured figures and 8 'specialists' (squad leaders, medics, mechanics, banner bearers, etc).

[marell le fou]

Fabulous sculpts, really. Those orks are incredible. Good job, Malika !

[Stormwind]

Oh man they'd make wonderful heavy armoured characters. <3

[Malika]

So this just happened...

Novan Elites Heavy Siege Armour Suppressors - £6.50

Suppressors are a support arm of the Novan Elites siege armour detachments, in addition to the regular equipment carried by such units they also carry overhead heavy grenade launcher pods. These launchers allow the squad to act as a mobile fire support formation and have proven quite effective in the suppression of both enemy ground units and the defenders of city walls and fortifications. Once the launchers have expended all munitions the empty pods can be ejected for greater mobility.

This set contains: 30 x Novan Elites heavy siege armour suppressors in five poses.

https://vanguardminiatures.co.uk/shop/novan-elites-heavy-siege-armour-suppressors/

[Malika]

By the way, would there be any interest in 6mm Gorkamorka and Necromunda Ash Wastes like stuff?

[Malika]

Cybershadow DT-60 Light Drone Tank - £7.00

The DT-60, Drone Tank type 60  is a common sight amongst Cybershadow battle groups, crewed by a single combat drone hard wired into the pilots position these tanks are considered as expendable units by Cybershadow command and are deployed en mass to overwhelm enemy forces. They also serve in the support roll alongside the heavier “Skitter” tank and Cybershadow infantry formations. The tank sports two hard points with machine guns, rocket pods and disruptors being reported as common armaments in use on this machine.

Set contains:

3 x DT-60 Upper hulls

3 x DT-60 Lower hulls

12 x Leg units

9 x Weapons, 3 x twin MG’s, 3 x rocket pods, 3 x disruptors

https://vanguardminiatures.co.uk/shop/cybershadow-dt-60-light-drone-tank/

And next to the Skitter tank for scale:

[Malika]

Beginning of a possible new project?

[Malika]

From left to right: WIP of a close combat fellow, gang leader, flamer guy, Vanguard Miniatures' Cybershadows Stalker Pilot, Vanguard Miniatures' Novan Elites Siege Armour.

[Stormwind]

Very nice!

[Malika]

Thanks! I really hope we can get these off the ground, kinda depends wether we can find a party willing to produce and distribute these. Still a bit too early to say for now.

[Malika]

[Malika]

[Malika]

I designed a semi generic bridge kit for Vanguard Miniatures






https://vanguardminiatures.co.uk/shop/single-bridge-span-6mm/

A resin cast generic human bridge span with a slot on the inner faces for insertion of a 2mm thick plastic sheet or MDF (not included) road to whatever width you desire.

Set contains:

2 x bridge spans

4 x optional bridge legs

6 x optional barriers

Span dimensions: 48mm long, 25mm high. Additional legs 20mm high each.

Infantry figure and 50mm square plastic road tile shown for scale purposes only and is not included in this set. Note also that the resin colour may vary.